PARAMETER | -RCC |
Purpose | This parameter defines the type of compression applied to CCITT files. |
Values | 0
-- Group III 1D 1 -- Group IV |
Use | CCITT, TIFF |
PARAMETER | -RFC |
Purpose | This parameter defines the type of compression applied to fax files. |
Value | 0 -- Group III 1D |
Use | FAX, AWD, WinFax, IOCA, IOCAMO, CALS |
PARAMETER | -RWD |
Purpose | This parameter defines the width of the raster output image in pixels. |
Notes | Default value: 400 |
Use | With all raster formats |
PARAMETER | -RHT |
Purpose | This parameter defines the height of the raster output image in pixels. |
Notes | Default value: 400 |
Use | With all raster formats |
PARAMETER | -RQL |
Purpose | This parameter defines the image quality of a JPEG image. |
Values | The range is 2 (Lossless) to 100 (Lossy Ð very coarse) |
Notes | Default value: 2 |
Use | JPEG only |
PARAMETER | -RBP |
Purpose | This parameter defines width of the output raster image in pixels. |
Notes | Default value: 400 |
Use | With all graphic formats |
PARAMETER | -REM |
Purpose | This parameter applies the English mode to this conversion. |
Values |
0 = Inch 1 = Foot |
Use | You must enter both -RBE and -RTE parameters and values following this parameter, to establish the scaling ratio. |
PARAMETER | -RBE |
Purpose | This parameter defines the English mode scaling denominator value. |
Values | Enter the numerator value after typing this parameter. |
Use | This (in combination with -RTE) sets the percentage of scaling applied in the English mode, for use with all formats. |
PARAMETER | -RTE |
Purpose | This parameter defines the English mode scaling numerator value. |
Values | Enter the denominator value after typing this parameter. |
Use | This (in combination with -RBE) sets the percentage of scaling applied in the English mode, for use with all formats. |
PARAMETER | -RMD |
Purpose | This parameter defines a resolution mode—absolute or dots per inch. |
Values |
0 = Absolute 1= Dots per inch |
Use | If you choose "DPI", you must enter the -RDM and -RDPI parameters to establish the actual DPI resolution. |
PARAMETER | -RDPI |
Purpose | This parameter defines the DPI resolution. |
Values |
0 = 200 dots per inch (DPI) 1= 300 dpi 2 = 400 dpi |
Use | This parameter establishes the values of "dpi" if that option is selected by means of the -RMD parameter. |
PARAMETER | -RDM |
Purpose | This parameter defines the basic output mode--allowing you to pick from dots per inch, paper size, English or Metric modes. |
Values |
0 = DPI 1 = Set to paper size 2 = English 3 = Metric |
Use | All formats. |
PARAMETER | -RMM |
Purpose | This parameter defines the metric mode. |
Values |
0 = millimeter 1 = meter |
Use | This parameter should be followed by the -RMT parameter, for use with all formats. |
PARAMETER | -RMT |
Purpose | This parameter defines the value of the base metric unit. |
Values | Enter the base metric value after typing this parameter. |
Use | This parameter should follow the -RMM parameter, for use in all formats. |
PARAMETER | -RSZ |
Purpose | This parameter defines the paper size. |
Values | 0 -- A (Default) 1 -- B 2 -- C 3 -- D 4 -- E 5 -- A0 (zero) 6 -- A1 7 -- A2 8 -- A3 9 -- A4 |
Use | All formats |
PARAMETER | -RTF |
Purpose | This parameter defines the type of TIFF file to create. |
Values | 3 -- RGB with no compression (Default) 86 -- CMYK with no compression 87 -- RGB with Packbits compression 88 -- CMYK with Packbits compression 93 -- YCC with no compression 95 -- YCC with Packbits compression |
Use | TIFF only |
ED: 10.05.00 -- jsm | Contents Copyright © 2000, Tailor Made Software, Ltd.